No S-Video out on T22 - need help.

Message

Nolonemo · #1 Post by **Nolonemo** » Sat Dec 03, 2005 12:24 pm

I am not getting anything on the TV when I connect it to the T22 using a 4-pin s-video cable and toggling to external monitor display on the T22.

If I connect the cable to the s-video out on my desktop PC's video card, I get a display on the TV, so the problem does not appear to be with the cable or the TV.

Am I missing something? I've looked in the TP configuration utility on the T22, but don't see anything about the s-video port.

Thanks.

Orevin · #2 Post by **Orevin** » Sun Dec 04, 2005 10:58 pm

Maybe this will help:

http://www-307.ibm.com/pc/support/site. ... R-58625#s3

Nolonemo · #3 Post by **Nolonemo** » Mon Dec 05, 2005 4:14 pm

AHAH! That should do the trick. Thank you!

Guest · #4 Post by **Guest** » Fri Dec 23, 2005 11:19 am

Great, I tried hooking my T23 up to my tv and got very frustrated. Great post thanks for the help.

Shack80 · #5 Post by **Shack80** » Sat Jan 07, 2006 8:11 am

Thanks o this thread I got my t23 working on my TV, but I have an issue! On my tosh hfx84(1080i hdtv crt) To see the whole screen I have to pan around, the entire screen is not shown. Is there a setting in XP to make it all fit or is this a limitation of the graphics chip? I know my 7500 aiw converts its signal to 480i just fine with no need to pan. I imagine some of my terminolgy is wrong, sorry if it is confusing.

p.s. I was the guest who posted before, not sure why that happened.

#6 Post by **carbon_unit** » Sat Jan 07, 2006 9:11 am

You probably need to adjust the display properties for the TV out to 640x480 or so.

NTL1991 · #7 Post by **NTL1991** » Thu Jan 12, 2006 8:21 pm

And if you dont see 640x480 and you only see 800x600, you can go into display properties, then click Advanced, then go into the adapter tab and click List all Modes, then hit 640 by 480 and then hit apply...

I dont know if your TP's minimum is 800x600 or you can just skip this then...

Nick

briank · #8 Post by **briank** » Fri Mar 17, 2006 7:43 pm

Aparently I don't have the proper s3 driver installed because that IBM support page shows tabs that aren't present on my advanced display window.

Orevin · #9 Post by **Orevin** » Fri Mar 17, 2006 8:37 pm

For Win9x/Me: http://www-307.ibm.com/pc/support/site. ... IGR-4JRMXT
For Win2k/XP: http://www-307.ibm.com/pc/support/site. ... IGR-4JRNJB

briank wrote:Aparently I don't have the proper s3 driver installed because that IBM support page shows tabs that aren't present on my advanced display window.

briank · #10 Post by **briank** » Sun Mar 19, 2006 9:35 am

Thanks. I now see the TV option, but I can't select it (greyed out). Oh well. I don't need the S-video output, just would have been nice from time to time.

Orevin · #11 Post by **Orevin** » Sun Mar 19, 2006 11:15 am

The TV option only becomes active, when the TV is connected. Maybe you even have to reboot with the cable connected and the TV running.

#12 Post by **JHEM** » Sun Mar 19, 2006 2:09 pm

Orevin wrote:Maybe you even have to reboot with the cable connected and the TV running.

Correct!

Regards,

James

No S-Video out on T22 - need help.

No S-Video out on T22 - need help.

Who is online